Knowing Plumbing Basics is Essential When Installing a Bathtub
Knowing Plumbing Basics is Essential When Installing a Bathtub
Blog Article
They are making a few great annotation related to How to Install a Bathtub overall in this article following next.
Mounting a tub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a new one is also a moderately difficult task. If the old tub is readily accessible, the job can move easily; if you have to open up a wall to eliminate the old tub and place the brand-new bathtub, the job is much harder. In either case, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have certified yourself for the job and fit attempting it. Rather than employing a specialist to take over a halfway-completed task, it is better to take into consideration utilizing one before you start. Opportunities are you may require a professional plumber to make tube links.
This write-up will certainly aid you mount a new bath tub in your shower room if you have actually currently gotten a brand-new bathtub and also don't need to change the plan of your previous water pipes.
Your tools and product checklist ought to make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you should do is detach the water. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin making certain that the washing machines are in area between the faucet as well as the sink. Secure the faucet in position with the manufacturer given backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind must be attached to the faucet ends first, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the called for position. The wooden boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bathtub till the spirit level reviews degree.
To set up faucets, fit all-time low of the outermost versatile tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the supply of water and examine all joints and also brand-new pipework for leaks and also tighten them if essential. Fill the bathtub as well as also check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bath tub has been made use of at least once as this will settle it into its last position.
Planning for the Installment
To start with, the sustaining framework provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is very important to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can split relatively very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
We were shown that write-up on How to Install a Bathtub Yourself through an associate on another blog. Sharing is good. Helping people is fun. I enjoy reading our article about Installing A Bathtub.
Trusted plumbing emergency service awaits. Report this page